9S-4185 PLUG Caterpillar D10T за продан - Мароко

Цена без ДДС
29 BGN
162 MAD
Цена без ДДС
29 BGN
162 MAD
[Other] 9S-4185 PLUG Caterpillar D10T

ОСНОВНИ СВЕДЕНИЯ

Продуктова групаДруги компоненти
Марка /Модел9S-4185 PLUG Caterpillar D10T
Местоположение на машинатаAgadir
Страна
Mascus ID00F0AA4C
+ Покажи повече подробности

ЦЕНИ

Избери валута
Цена без ДДС29 BGN  (162 MAD)
ДДС
Цена с ДДС-

ХАРАКТЕРИСТИКИ

Брой на вътрешния инвентар9S-4185
Производствен номер9S-4185
Delivery termsEXW
Друга информацияCare must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
The engine is equipped with an Electronic Control Module (ECM). The ECM contains no moving parts. Follow the troubleshooting procedures in this manual in order to be sure that replacing the ECM will correct the problem. Verify that the suspect ECM is the cause of the problem.Note: Ensure that the ECM is receiving power and that the ECM is properly grounded before replacement of the ECM is attempted. Refer to the schematic diagram.A test ECM can be used in order to determine if the ECM on the engine is faulty. Install a test ECM in place of the suspect ECM. Install the flash file with the correct part number into the test ECM. Program the parameters for the test ECM. The parameters must match the parameters in the suspect ECM. Refer to the following test steps for details. If the test ECM resolves the problem, reconnect the suspect ECM. Verify that the problem returns. If the problem returns, replace the ECM.Note: If an ECM is intended to be used as a test ECM, "Test ECM Mode" must be selected on the electronic service tool before the engine serial number is entered.Use the electronic service tool to read the parameters in the suspect ECM. Record the parameters in the suspect ECM. Install the flash file into the new ECM. After the ECM is installed on the engine, the parameters must be programmed into the new ECM.Note: When a new ECM is not available, an ECM can be used from an engine that is not in service. The ECM must have the same serial number suffix. Ensure that the replacement ECM and the part number for the flash file match the suspect ECM. Be sure to record the parameters from the replacement ECM. Use the "Copy Configuration ECM Replacement" function in the electronic service tool.
If the flash file and engine application are not matched, engine damage may result.
Perform the following procedure in order to replace the ECM.
Connect the electronic service tool to the diagnostic connector.
Use the "Copy Configuration ECM Replacement" function from the electronic service tool. If the "Copy Configuration" is successful, proceed to Step 4. If the "Copy Configuration" failed, proceed to Step 3.Note: Record any Logged Faults and Events for your records.
Record the following parameters:
Record all of the parameters on the "Configuration" screen.
Record all of the parameters on the "Throttle Configuration" screen.
Record all of the parameters on the "Mode Configuration" screen.
Record the serial numbers of the electronic unit injectors. The injector serial numbers are
STEP ABDELMOUMEN -
  • +212...SHOW
    Please mention MASCUS when you contact the seller
  • WhatsApp
    +212 774693591
Send e-mail

Contact Person

  • A. TYAL

    STEP ABDELMOUMEN -
    • +212...SHOW
      Please mention MASCUS when you contact the seller
    • ...SHOW
      Please mention MASCUS when you contact the seller
    • Данни за връзка с програма за съобщения:
    • WhatsApp
      +212 774693591
    • Езици: Френски
    • Immeuble des forces Auxiliaires SAMLED, Avenue Mohammed V, 80000 Agadir, Мароко

Фирма:

STEP ABDELMOUMEN -

2
ГОДИНИ АКТИВНОСТ В MASCUS
Всички реклами
Report suspicious display
Сродни марки
МаркаБрой обяви
Caterpillar34207
Volvo8961
Liebherr8785
Komatsu7088
JCB4321

Това обявление за [Other] 9S-4185 PLUG Caterpillar D10T други компоненти е поместено в Mascus - търговски сайт за машини и оборудване втора ръка. Характеристики - Брой на вътрешния инвентар: 9S-4185, Производствен номер: 9S-4185, Delivery terms: EXW